Window Rough Opening Size and How to Frame It

A nail-fin window's rough opening is usually its frame size plus half an inch each way. How to size, frame and check openings so the windows fit.

For most nail-fin windows the rough opening is half an inch wider and half an inch taller than the window frame. A window with a 35 1/2 by 59 1/2 inch frame goes into a 36 by 60 inch opening. The extra half inch leaves about a quarter inch on each side to level, plumb and shim the unit. The allowance is set by the window manufacturer, so read the installation instructions or ask the supplier before the framer starts cutting.

Three numbers that get mixed up

A window has a frame size, the outside of the frame not counting the nailing fin. The wall has a rough opening, the framed hole between the jack studs and from the rough sill to the header. Then the plans have a call-out, the shorthand the designer wrote next to the opening.

The call-out is where it goes wrong. A 3050 on a plan usually means a window about 3 feet wide and 5 feet tall, but whether that's the rough opening or the unit size depends on who drew it and which catalog they had open. If the framer builds a 36 by 60 opening and the window shows up with a 36 by 60 frame, it doesn't go in.

Write on the window schedule which number each size is. When you send it to a supplier, say the same thing in the email. A supplier can work from either, as long as it knows which one it's looking at.

Measuring a framed opening

Windows are usually ordered from the plans, months before the openings are framed, so check each opening against the schedule once it's built. If the opening and the window don't agree, the framing is easier to fix before the windows arrive than on installation day.

  • Measure the width at the top, middle and bottom, between the jack studs.
  • Measure the height on the left, middle and right, from the top of the rough sill to the underside of the header.
  • Use the smallest width and the smallest height.
  • Measure both diagonals. If they don't match, the opening is out of square and the framing needs fixing before the window arrives.
  • Put a level on the rough sill and check the jack studs for plumb.

A window can be shimmed into an opening that's a little big. It can't be shimmed into one that's too small or badly out of square.

Framing it right the first time

The parts are familiar to any framer: king studs, jack studs carrying the header, the rough sill and cripples above and below. The mistakes to watch for are paperwork more than carpentry. An opening gets framed from an old schedule or from the call-out instead of the rough opening size.

Pick the head height for each floor and hold it, so the tops of the windows line up with each other and with the doors where the design calls for it. Mark each opening with its tag from the window schedule while the framing is open. The same tag goes on the window when it arrives, which makes it hard to put the tempered unit in the wrong hole.

Sill height on bedroom windows

An egress window needs the bottom of its clear opening no more than 44 inches above the finished floor, so allow for the flooring that goes in later. That's measured to the opening the window gives when it's open, not to the rough sill. The frame's own sill sits above the rough sill and adds height. So does any sill pan or shim under it. Frame the rough sill low enough that the clear opening still lands at or under 44 inches.

Bedroom egress window requirements has all four egress numbers and how each window type meets them.

Upper floors have the opposite problem. An operable window needs fall protection when its sill is less than 24 inches above the floor and the drop outside is more than 72 inches. If the design shows low sills upstairs, sort that out before the order goes in. Building departments can differ on these details, so confirm them with your plans examiner.

Getting the opening ready for the window

The opening is set up to shed water before the window goes in, which matters most on the wet side of the state. The sill gets its flashing or sill pan first and the house wrap is cut and folded the way the installation instructions show. Then the window is set and fastened through the fin. The jamb and head flashing are lapped over it in shingle order. The head flashing goes under the wrap above, never on top of it.

Converting rough openings to frame sizes

There's no single size chart that works for every brand, because each manufacturer sets its own allowance. With a half inch allowance the conversion is simple subtraction:

  • A 24 by 36 inch rough opening takes a 23 1/2 by 35 1/2 inch frame.
  • A 36 by 48 inch rough opening takes a 35 1/2 by 47 1/2 inch frame.
  • A 48 by 60 inch rough opening takes a 47 1/2 by 59 1/2 inch frame.
  • A 72 by 48 inch rough opening takes a 71 1/2 by 47 1/2 inch frame.

Width comes first and height second, the way window sizes are normally written.

If your windows are made to size, the openings don't have to land on stock dimensions at all. The window is built to the opening instead of the other way around, so there's no need for filler strips or reframing in the field.

Where we fit

Our windows are made to the rough openings on your schedule, in inches, with a vinyl frame and an integral nailing fin. The rough opening is the frame size plus half an inch in each direction. Send us rough openings or frame sizes, tell us which they are and we'll price the whole schedule. Lead time is 11 to 12 weeks from a locked order to the job site, so the order usually goes in from the plans. That's why we ask which size is which. Send your window schedule.

Ready to price your windows?

Ready to price
your windows?

Send us the window schedule and we will come back with product options and a factory-direct number.